The first step, wearing a film Yellow rice wine is a traditional Chinese alcoholic beverage made from glutinous rice, yeast, and water. It is commonly consumed during festivals and special occasions, and is also used in cooking. The wine is fermented in a jar, which allows the yeast to convert the rice starches into alcohol. The resulting wine is light and sweet, with a slightly nutty flavor. It is often served warm, and is believed to have medicinal properties. Shaoxing Yellow Rice Liquor,Little Jar Package Wine,Yellow Rice Liquor in Can,Sweet Taste Alcohol Zhejiang Shengta Shaoxing Wine Co., Ltd. , https://www.shaoxingyellowricewine.com
To get the film, you need to confirm the winding direction of the film, find the counterclockwise direction, and put it on the film rod to fix it. (Please turn off the power when wearing the film.) Pay attention to whether the front and rear fixing plates of the film are tightly combined with the film. If it cannot be tightly combined, use a utility knife to cut the inside of the film tube and then insert it. After wearing the film, use it. The adhesive tape is firmly attached to the receiving paper tube.
Hand chain sealing machine
Step 2, sealing operation steps (panel operation instructions)
Turn on the power, turn on the power switch, the indicator light is on, set the temperature controller to the predetermined temperature, and the green heating indicator lights up. When the upper hot plate reaches the predetermined temperature, the red constant temperature indicator lights up (the electric heating device alternates between heating and holding state when the sealing machine is working, so the green and red indicator lights are also alternately displayed, which is a normal phenomenon).
Put the plastic cup into the lower mold slide and push the lower mold slide to the determined position by hand (if it is a fully automatic sealing machine or automatic sealing machine, after placing the plastic cup, the lower mold slide will automatically enter), press down Hold the handle of the sealer to the maximum stroke, hold it for 1~2 seconds, then slowly raise the handle and push it to the original position. Pull out the lower mold slide, take out the plastic cup, and put it into the final sealing rubber cup for another cycle.
Cleaning and maintenance of the sealing machine:
Regularly clean the surface of the machine, the bottom plate and the lower die slide, the groove, the upper mold inner pressure plate and the positioning rod (Note: the power must be turned off and the normal temperature is restored).
The lower die slide, the pressure bar bearing, the eccentric wheel and the guide post, the guide rail and other transmission parts are regularly added with butter to ensure the performance of the machine.
To clean the cutter: first use the cotton ball to plug the two drain holes of the lower mold, pour the boiling water into the groove of the lower mold, fill it up, then push in
The lower mold slide is in place, press the upper mold down, press it to the lowest point, let the tooth cutter soak for several minutes until it is clean, and repeat it several times.
Sealing machine use precautions:
1. It is not suitable for metal containers and metal covers. It is not allowed to press the start button on the metal table, otherwise it will damage the machine.
2. Insert the induction air plug and tighten the screw before turning on the power.
3. Use single-phase three-wire power cord. For operator safety, be sure to use single-phase three-wire power socket. The work floor must be dry to keep insulation.
4, with temperature overheating automatic protection function, when the internal temperature of the machine is overheated, the buzzer sounds in the machine " abnormal protection (PRO.MD.)" yellow indicator light, at this time should turn off the main power switch, standby cooling After the buzzer stops, continue working.
5. During the working process, always touch the surface of the sensor head to check whether it is overheated. If it is found that the hot hand should stop heating, wait until it is cooled before working (cooling can not turn off the power), when the “WARMUP†green indicator light is off, please Do not press the start button to avoid false triggering. When the unit is finished, turn off the power switch on the panel.
6, equipped with a fuse of 5A, not available for greater than 5A insurance instead.
7. There is high voltage inside, the bottom plate is charged, and it is strictly forbidden to repair it personally to avoid personal electric shock.
8. If it is found that there is a bare wire before use, stop using the machine and use it after repair.
9. The equipment should not be impacted, stressed or damp when transported, stored or used.
10. When the product is inspected and checked out, in the case of normal transportation and good packaging, if the parts of the product are found to be inconsistent with the packing list, they should contact the company in time.