Pain Relief Patch for Breast
Pain Relief Patch For Breast,Pain Relief Plaster For Breast,Relief For Breast Pain,Pad Relief Patch For Breast Shandong XiJieYiTong International Trade Co.,Ltd. , https://www.xijieyitongpatches.com
[Name] Medical Cold Patch
[Package Dimension] 10 round pieces
The pain relief patch is composed of three layers, namely, backing lining, middle gel and protective film. It is free from pharmacological, immunological or metabolic ingredients.
[Scope of Application] For cold physiotherapy, closed soft tissue only.
[Indications]
The patches give fast acting pain relief for breast hyperplasia, breast fibroids, mastitis, breast agglomera tion, swollen pain.
[How To Use a Patch]
Please follow the Schematic Diagram. One piece, one time.
The curing effect of each piece can last for 6-8 hours.
[Attention]
Do not apply the patch on the problematic skin, such as wounds, eczema, dermatitis,or in the eyes. People allergic to herbs and the pregnant are advised not to use the medication. If swelling or irritation occurs, please stop using and if any of these effects persist or worsen.notify your doctor or pharmacist promptly. Children using the patch must be supervised by adults.
[Storage Conditions]
Store below 30c in a dry place away from heat and direct sunlight.
The demand for the experimental environment of the electronic tensile testing machine
The electronic tensile testing machine is divided into two series: digital display (liquid crystal display) and microcomputer control. The digital single-arm testing machine can be used with force values ​​below 10T, and the door type is used for 10T or more. Of course, with the use of As the value of force increases, the required machine configuration also needs to be upgraded, and there is naturally a gap in price. For some manufacturers or enterprises that need comprehensive and accurate analysis, you can use the microcomputer control series, which is also divided into single arm and gate type. The division of force values ​​is basically the same, all from 10N, 20N, 50N, 100N, 200N, 500N, etc. Specifications, electronic general products are up to 30T for the upper limit, but there are special requirements for our company in this regard for customers can be customized, do not worry about this.
Electronic tensile testing machine features and features:
1) Adopt high-precision, all-digital speed control system and precision reducer to drive the precision lead screw pair to test, realize the wide range adjustment of test speed, low noise and stable operation during test.
2) Touch key operation mode, the LCD display is displayed in real time. The display interface can display the test method selection interface, the test parameter selection interface, the test operation, the result display interface and the curve display interface, which are convenient and quick.
3) The electronic tensile testing machine can realize the lifting and lowering of the beam when the sample is clamped, and has the functions of overload protection.
4) Optional computer interface, external computer can be used to realize the control of the test process and data storage and printing.
What are the requirements for the experimental environment of the electronic tensile testing machine?
Generally, the test environment of the electronic tensile testing machine determines the accuracy of the test data, the integrity of the test equipment, etc., so in order to obtain accurate test data, the environmental requirements related to the electronic tensile testing machine should be strictly observed. Generally speaking, it can be divided into six categories. This is just a general introduction. When using the electronic tensile testing machine, users must follow the relevant standards of the corresponding materials.
1. The laboratory space must be larger than the size of the electronic tensile testing machine itself, such as the vertical electronic tensile testing machine model, such as the 3 m ring stiffness testing machine. For the convenience of testing and placement, the laboratory space should at least It is 4 meters; for horizontal electronic tensile testing machines, the space of the laboratory is up to several tens of meters because of its unique test space requirements.
2. The humidity of the thermometer in the laboratory must be controlled within a certain range. If the test temperature is too high, it is easy to increase the frequency of failure of the motor and sensor of the test equipment. If the indoor humidity is too high, the equipment will be produced. Rust, in short, if there are no special requirements, all materials are required to be in the range of room temperature 10 ° C -35 ° C, and the relative humidity is not more than 80%.
3. The ground at the position where the electronic tensile testing machine is installed must be flat and stable. If it is not flat, the electronic tensile testing machine will inevitably produce a certain inclination, so the upper and lower clamps of the clamp cannot maintain the coaxiality. The test results have a great impact.
4. The power supply voltage in the laboratory should be stable and cannot fluctuate too much back and forth. It is similar to household appliances. The voltage fluctuation is too large, and the electrical switch back and forth will cause the electrical appliance to malfunction. Equipment that is typically fluctuating like an electronic tensile tester should not exceed ±10% of the voltage.
5. Corrosive media around the electronic tensile testing machine is absolutely impossible. After all, the testing equipment is metal products. Once the electronic tensile testing machine is damaged, it will reduce the mechanical properties such as strength, plasticity and toughness of the metal material.
6. The laboratory where the electronic tensile testing machine is located should not have vibration. If the vibration is generated during the test, it will affect the test data, and if it is in this case for a long time, it will cause the sensitivity of the sensor, encoder, etc. .
Want to know more about the electronic tensile testing machine , please pay attention to the company.