2020 amazon women massager masturbators pussy for male comfortable masturbator, Sex vibrator Silicone male Masturbation with USB Charging. Automatic Sucking Masturbator Sex Toys Male Masturbator Cup Masturbator for Man Vibrating Cup Pussy For Man. amazon women massager masturbators.Can use warm water, shower gel to clean, wipe with a rag to clean water, and then stored in a ventilated place to dry! Hands Free Male Masturbators,Adult Masturbation Cup,Sex Masturbators Toy,Man Sexy Toy Masturbators Shenzhen Joyfun Sex Toys Co.,Ltd. , https://www.joyfunsextoys.com
(2) Commissioning: After installing the punch and the die, the weight and hardness can be adjusted. The feeder needs to be connected to the feed bucket and close to the mold base. Add a small amount of granules to the feed hopper and turn the machine by hand while rotating the pressure adjustment wheel until the complete tablet is pressed out. Check the quality of the tablets and adjust the tablet weight to meet the requirements: before obtaining a satisfactory tablet weight, it is often necessary to make multiple adjustments: When the filling amount is reduced, the pressure must be reduced to give the tablets the same hardness. Conversely, when the slope charge increases, the pressure must be increased to obtain a phase hardness. Add the granules to the feed bucket and turn it on. Immediately after the start of operation, check the weight and hardness of the piece and adjust it as needed. These indicators are routinely inspected every 15-30 minutes, and the machine remains continuously running during the inspection:
(3) Cleaning: When the particles are consumed, turn off the power. Remove the feed and feed from the machine and use a vacuum cleaner to remove loose particles and dust: Rotate the pressure adjustment wheel to a low pressure. Remove the punch and die ring in the reverse order of installation, wash with ethanol, remove the attachment with a soft brush, then dry with a clean cloth, apply a thin layer of oil and store.
(4) Maintenance and maintenance: Regular inspection of the machine parts, 1-2 times a month, the inspection items are worm gear, worm, bearing, pressure wheel, crankshaft, upper and lower rails, whether the movable parts are flexible and wearable, and the defects should be timely Repair: After the tablet press is finished, the workplace and machinery will be thoroughly cleared according to the “Clearance Management Systemâ€. If it is not used for a long time, apply anti-rust oil on the smooth surface of the machine. Cover it with a cloth cover: the maintenance of the die should be placed in a covered metal box. The sex die is all immersed in oil or coated with anti-proof. Rust oil and keep it clean and free from rust and bruises. To do the lubrication of the tablet press, according to the type of oil cup, note the butter or oil separately, and all should be refueled before driving. In the middle of the way, depending on the situation, the bearings of the glass turntable on the upper cover should be inspected for oil in the cup. If there is no oil or low oil, oil should be injected. The screw and oil cup on the worm are lubricated worm gears. In operation, the oil is added according to the actual situation: the two ends of the drive shaft are equipped with wave bearings, and the outer casing of the shaft shell can be refueled once a week and pressed with a grease gun. The tail of the punch and the curved guide rail are lubricated with butter, taking care not to overdo it and prevent oil stains. During use, if the equipment emits abnormal noise or other abnormal conditions, it should be stopped immediately and checked before being used.
This product is efficient, simple, comfortable, safe, can be used with lubricants, adult appliances and water
Note: please keep hygiene before and after use
soft and comfortable, bring you mind-blowing orgasms.
Use and maintenance of rotary multi-punching machine
Use and maintenance of rotary multi-punching machine (1) Installation: first adjust the pressure, reduce the pressure of the machine, and then load the punch and the die. The die hole must be clean and there should be no other contaminants: loosen the die ring tightly with the screw, gently insert the die ring into the die hole, and then gently tap the die with a metal rod wrapped with soft fiber to make it accurately reach Pre-determined location. After all the mold rings are installed, tighten the screws and check that the mold ring is fixed. The undershoot is loaded from the mechanical preset hole by rotating the machine shaft. After all the punches are installed, they are loaded with punches. The end of the punch must be coated with a layer of mineral oil before installation. Adjust the film cam so that the lower punching position is flush with the die table.